This report is an outcome of a master degree project at Linköpings University in co-operation with Micronic Laser Systems AB. The purpose with this master degree project was to investigate how to implement a receiver in a data transfer system. The system consists of several data channels, where every channel consists of three parts: driver, transmission lines and receiver. The driver send low amplitude differential signals via the transmission lines to the receiver that amplifies and converts it to a single-ended signal. The receiver has to be fast and be able to feed an output signal with high voltage swing.

This report present the design and manufacturing of a wide-band driver amplifier placed in radar module for airborne applications. The major goals for the amplifier were a high efficiency and to deliver a predefined output power. To reach the second goal an additional preamplifier had to be constructed. The amplifiers were constructed in three steps: Design and Layout in the software Microwave Office, Mounting components and Verification. The driver amplifier was decided to be a push pull configuration consisting of two parallel transistors biased in class AB.

Softube has developed DSP-card and software for simulation of the sound of old tube amplifiers. The purpose with this thesis is to design a compact amplifier with high power to function together with the DSP-card and build a unit that can replace several other guitar amplifiers. The advantages with that kind of solution could be that it would be cheaper, easier to carry and easier to stor than the real amplifiers. The amplifier that has been designed is of class D type with digital PWM modulator. There is several types of amplifier modules on the market that use analog input signal, but if one of them would be used a D-A converter is needed on the DSP card.

The purpose with the report is to show that it is possible to design a class-D amplifier, using a programmable FPGA mounted on a developing card from Xess and a H-bridge. The FPGA was programmed in VHDL which is the language the software from Xilinx use to implement a logical function into the FPGA The logical function corresponds to a modeling of the music signal and the modeling can be described as a comparator which compare the music signal with a triangle wave and as a out signal produce a pulse width modulated (PWM) signal. The report is also a review and evaluating of two different modulating technologies, AD- modeling and BD-modeling. A detailed part about how the H-bridge was designed and how it works. The result of this project is a working audio amplifier to a significant lower price than the products in todays market..

The last few decades the development in the field of electronics has been huge. The components performance gets better at the same time as the manufacturing cost decreases. Many of the design moments that have to be done, are done automatically today, but it can get better. Especially for analog circuit design.At Electronic System in Linköpings universitet, research is in progress to develop a tool that can design analog circuits in reasonable time. It means that it has to size the components (transistors, resistances, capacitances etc), so that the circuit can fulfill the performance requirements.

This paper describes a method for wireless energy transfer via near-field electromagnetic inductionthat is inexpensive, simple and can be applied to almost any type of system, regardless of size andenergy demands.The method uses a primary unit consisting of an oscillator, amplifier and inductive coil thattransfers energy to a secondary unit consisting of a coil, rectifier and voltage regulator. Two typesof oscillators and several amplifier designs were realized and evaluated together with a multitudeof flat coils of both monofilar and bifilar type.The results show that it is important to use an oscillator whose frequency is dependent on theinductance of the connected transmission coil, such as the Colpitts oscillator. This is preferable toan oscillator with a preset frequency, such as a Schmitt-trigger oscillator..

This paper describes a method for wireless energy transfer via near-field electromagnetic inductionthat is inexpensive, simple and can be applied to almost any type of system, regardless of size andenergy demands.The method uses a primary unit consisting of an oscillator, amplifier and inductive coil thattransfers energy to a secondary unit consisting of a coil, rectifier and voltage regulator. Two typesof oscillators and several amplifier designs were realized and evaluated together with a multitudeof flat coils of both monofilar and bifilar type.The results show that it is important to use an oscillator whose frequency is dependent on theinductance of the connected transmission coil, such as the Colpitts oscillator. This is preferable toan oscillator with a preset frequency, such as a Schmitt-trigger oscillator..

A current conveyor is an active building block that can be used to implement most active and passive components. It differs from the operation amplifier in that it uses current instead of voltage. The current conveyor also has significantly higher voltage gain over a broader frequency range. To simplify the construction of analogue circuits and increase the construction efficiency it is desirable to use a top-down methodology. This means that the whole system is partitioned into a hierarchy of subsystems.

In this Master's thesis, a direct-conversion receiver front-end has been designed in a 0.18um CMOS technology. Direct-conversion receivers (DCR) have obvious advantages over the heterodyne counterpart. Since the intermediate frequency (IF) is zero, the problem of image is circumvented. As a result, no front-end image reject filter is required and the channel selection requires only a low-pass filter, which makes it easy to integrate directly on chip. However, the DCR also suffers from several drawbacks such as extreme sensitivity to DC offsets, 1/f noise, local oscillator (LO) leakage/radiation, front-end nonlinearity and I/Q mismatch.

Arbetet handlar om hur upphovsmannen komponerade och arrangerade musik till en gradvisväxande ensemble till sin popmusikal. Kompositören har reflekterat över vilka uppgifter varjemusiker tilldelades i olika sångnummer inom den instrumentala ensemblen. Precis somskådespelare har olika roller inom en pjäs har musiker olika roller inom en låt.Ett mål med musikalen var ett skapa en udda och unik ensemble då musikerna även medverkade ihandlingen. Upphovsmannen valde tio olika instrument samt bestämde turordning för dem. I detförsta sångnumret medverkar endast piano, i det tionde och sista består ensemblen av piano, elbas,trummor, trumpet, cello, elgitarr, cembalo, trombon, klarinett och flöjt.

Detta arbete har utförts tillsammans med FOA 3 i Linköping som en undersökning av molntextur och molnklotter i flygbilder som registrerar värmestrålning. I dessa sammanhang betyder klotter en slags spräcklighet i bilden, eller att det inte går att se några mönster och strukturer i den..

In this report we describe an adaptive simulated annealing method for sizing the devices in analog circuits. The motivation for use an adaptive simulated annealing method for analog circuit design are to increase the efficiency of the design circuit. To demonstrate the functionality and the performance of the approach, an operational transconductance amplifier is simulated. The circuit is modeled with symbolic equations that are derived automatically by a simulator..

Att ansluta en digital signalprocessor kräver ett omfattande arbete. Innehållet i denna rapport sammanfattar teoretiska metoder för att integrera den digitala signalprocessorn ADAU1701 i talförstärkaren MMT-4, utvecklad av företaget Xena Medical. Arbetet har till största delen bestått i att finna en lämplig DSP och studera dess datamanual för att anpassa den till talförstärkaren.Mycket av rapporten sammanfattar beräkningar av komponentvärden och anpassning av ADAU1701 för MMT-4:s behov. ADAU1701 beskrivs utifrån det så kallade selfboot-läget där processorn kan arbeta som fristående processor..

Allt större och större andel företag väljer att presentera och förmedla varor och tjänster via e-handel. En viktig aspekt vid e-handel är att kunden känner förtroende för e-handelsapplikationen och företaget. Denna rapport redogör för vilken inverkan multimediala inslag har för förtroendet av en e-handelsapplikation, vid initialt användande. En undersökning har genomförts med hjälp av en kooperativ utvärdering av fyra e-handelsapplikationer vilka innehåller olika typer av multimediala inslag har.Resultatet av undersökningen visar att multimediala inslag inverkar positivt på förtroendet för e-handelsapplikationer. Däremot finns indikationer på att för hög grad av multimedialt inslag inverkar negativt på förtroendet för e-handelsapplikationer..

This work aims to obtain information on diurnal variations of aerosol concentrations in thecity of Lund (Sweden) and trying to locate the origin of the aerosols long distance transports.The study shows that the aerosol concentrations varied quit strongly over the entiremeasurement period, reflecting air masses of different degrees of pollution, mainly as a resultof the diurnal rhythm of the traffics. Trajectories reveals that air masses originated inSoutheastern and Eastern Europe contains higher aerosol concentrations compared to other airmasses..